International Technical Advisory Committee
	Professor Qing Liu
		•	BEng, Chongqing University, 1984
		•	MEng, Harbin Institute of Technology, 1987, "TEM Study of Precipitates in a High Strength Aluminum Alloy"
		•	MEng, Harbin Institute of Technology, 1991, "Deformation Mechanism of a Superplastic Al-Li-Cu-Mg-Zr Alloy"
	Dean
		Department of Materials Science and Engineering Tsinghua University Tsinghua, Beijing, 100084, China
		Phone: +86 (010) 6277 2852 Fax: +86 (010) 6277 3302 Email: qing.liu@mail.tsinghua.edu.cn
	Research interests/Biography
	•	Mechanisms and control of Macro- and Micro- texture in metallic materials (including metal deformation, work hardening, recovering and recrystallization)
	•	Superconductivity materials
	•	Plastic deforming techniques for metals and metal-based composite materials (including rolling, tension and superplastic shaping)
	•	Microstructure and orientation measurement techniques (including orientation measurement in TEM and EBSD in SEM)
	Selected publications
	1.	Qing Liu, Huang Xiaoxu & Yao Mei, "On Deformation Induced Continuous Recrystallization in a superplatic Al-Li-Cu-Mg-Zr alloy", Acta Metall. Mater., 40 (7), P. 1753-1762, 1992.
	2.	Qing Liu, "A Simple Method of Determining Orientation and Misorientation of the Cubic Crystal Specimens", J. Appl. Cryst., 27, 755, 1994.
	3.	Qing Liu, Yang Wangyue & Chen Guoliang, "On Superplasticity of Two-Phase-Titanium-Inermetallic Ti-(Co,Ni)-Al Alloys", Acta Metall. Mater., 43, p. 3571-3582, 1995.
	4.	Qing Liu & N. Hansen, "Deformation Microstructure and Orientation of FCC crystals", Phys. Stat. Sol.(a), 149, 187, 1995.
	5.	Qing Liu & N. Hansen, "Geometrically Necessary Boundaries and Incidental Dislocation Boundaries Formed During Cold Deformation", Scripta Metall. Mater., 32, 1289, 1995.
	6.	Qing Liu, "A Simple and Rapid Method for Determining Orientation and Misorientation of Crystal Specimen in TEM", Ultramicroscopy, 60, 81, 1995.
	7.	J.A. Wert, Qing Liu & N. Hansen, "Dislocation Boundaries and Active Slip Systems", Acta Metall. Mater., 43, 4153, 1995.
	8.	Qing Liu & N. Hansen, "Microstructural study of deformation in grain boundary region during plastic deformation of polycrystalline aluminium", Mater. Sci. & Eng., 234, 672, 1997.
	9.	D.A. Hughes, Qing Liu, et al., "Scaling of Microstructural parameters: misorientations of deformation induced boundaries", Acta Mater., 45, 105, 1997.
	10.	Qing Liu, Cl. Maurice, J. Driver & Hansen N., "Heterogeneous Microstructures and Microtextures in Cube-oriented Al Crystals After Channel Die Compression", Metall. Mater. Trans. A., 29A, 2333, 1998.
	11.	Qing Liu, D. Juul. Jensen & N. Hansen, "Effect of Grain Orientation on the Deformation Structure of Cold-rolled Polycrystal Aluminium", Acta Mater., 46, 5819, 1998.
	12.	Qing Liu & N. Hansen, "Macroscopic and Microscopic Subdivision of a Cold-rolled Aluminium Single Crystal of Cubic Orientation", Proc. R. Soc. Lond. A., 454, 2555, 1998.
	13.	M. Richert, Qing Liu & N. Hansen, "Microstructural Evolution Over a Large Strain Range in Aluminium Deformed by Cyclic-extrusion-compression", Mate. Sci. & Eng. A., 260, 275, 1999.
	14.	Qing Liu, J. Wert & N. Hansen, "Location-dependent Lattice Rotation and Shear Strain in Rolled Alminium Single Crystal of Cube and Goss Orientations", Acta Mater., 48, 4267, 2000.
	15.	Z.J. Li, A. Godfrey & Qing Liu, "Macroscopic Sub-Division of Rolled Al-1%Mn Single Crystals of {001}<110> Orientation", Scripta Mater., 45, 847, 2001.
	16.	G.L. Wu, A. Godfrey & Qing Liu, "Macroscopic Subdivision Of Columnar Grain Aluminium With {001}<uv0> Orientations Following Low Strain Deformation", Scripta Mater., 45, 1117, 2001.
	Back to ITAC members